PS3 (Research/Experimental) - NEC/TOKIN Capacitors Replacement - YLOD

[Coro]

harika bilgiler teşekkürler seni seviyorum

English:
great information thanks i love you

hello and welcome to the website! please remember to post in English or provide a translation.

 

[cryptblood1986]

Also, these will work too. PANASONIC EEFSX0D331E4. They're 330ohms, so you would need to use 4 to replace each tokin, but they're much cheaper than the tantalum. you can get 32x $8.

Thanks I fixed 2 CECHA's with your advice.

I'm doing a cech 20xx slim right now. Do I do 3x 330 caps per Tokin also?

 

[sandungas]

Found these caps in a limited edition ps3 ryu ga 3 not sure if this has been found or not but these dont have nectokin writen on it also the console was never opened only opened it as arrive damaged but still works (motherboard is ver-001) trying to but every type on the limited editions to see any differences

The PS3 special editions sometimes uses components that differs a bit from the mass produced retail PS3 models. Your tokins are the same used in PS3 model DECR-1400. Motherboard https://www.psdevwiki.com/ps3/DEB-001
Are labeled different but seems to have the same specs, 1200ohm

Btw, can you make a photo of the sycon in that motherboard ?... or at least mention his name ?, we are still trying to find an special syscon model that was used in VER-001 motherboards, and your console seems to a be a good candidate for using it

 

[RIP-Felix]

Thanks I fixed 2 CECHA's with your advice.

How do you know? Hint, "I did the tanatalum thing and it worked" is not the right answer.

I'm doing a cech 20xx slim right now. Do I do 3x 330 caps per Tokin also?

3x would replace 1000uF with 990uF, but 1 extra will help compensate for the AlPol caps being inferior (to some extent).

 

[Djudju]

Hi @Djudju ...to get your PS3's Syscon error log you don't need CFW or HEN, infact you don't even need the PS3 to turn on. Here is Felix's guide on how to do it. Start at "If your console doesn't turn on" ...have a read through the guide, opening all the "Spoiler" tabs and you will get a good idea of what it's about:-
https://www.psx-place.com/threads/r...s-replacement-ylod.25260/page-192#post-295119

The Syscon error log from your PS3 will help you identify the problem.

Hello everyone, I managed to install a CFW, not brick. Then I installed pkg advanced tools. I have thisFirmware Version: 4.88 (build 50731)
Platform ID: CokF10
Product Code: 00 85
Product Sub Code: 00 08
Hardware Config: 4E00FFFF0307BCBF
Syscon Fimware Version: 065D.0000000000000000 (EEPROM: 0000000000000000)

Bringup Count: 3637, Shutdown Count: 3587
Runtime: 220 Days, 11 Hours, 42 Minutes, 49 Seconds

Error Log
01: A0802124 Sun Jan 15 04:12:46 2006
02: A0801002 Sun Jan 15 04:12:45 2006
03: A0802124 Wed Jan 11 16:37:15 2006
04: A0802124 Wed Jan 11 16:37:14 2006
05: A0801002 Wed Jan 11 16:37:14 2006
06: A0802124 Wed Jan 11 03:14:34 2006
07: A0801001 Wed Jan 11 03:14:34 2006
08: A0802124 Mon Jan 9 22:29:31 2006
09: A0801002 Mon Jan 9 22:29:31 2006
10: A0802124 Mon Jan 9 21:55:01 2006
11: A0801002 Mon Jan 9 21:55:01 2006
12: A0802124 Mon Jan 9 03:58:01 2006
13: A0801002 Mon Jan 9 03:58:01 2006
14: A0802124 Mon Jan 9 03:27:42 2006
15: A0802124 Mon Jan 9 03:27:42 2006
16: A0801002 Mon Jan 9 03:27:41 2006
17: A0802124 Fri Jan 6 21:30:13 2006
18: A0802124 Fri Jan 6 21:30:12 2006
19: A0801002 Fri Jan 6 21:30:12 2006
20: A0802124 Fri Jan 6 19:15:53 2006
21: A0801002 Fri Jan 6 19:15:52 2006
22: A0802124 Wed Jan 4 21:22:02 2006
23: A0801002 Wed Jan 4 21:22:01 2006
24: A0802124 Wed Jan 4 19:14:07 2006
25: A0801002 Wed Jan 4 19:14:06 2006
26: A0802124 Wed Jan 4 14:47:48 2006
27: A0801002 Wed Jan 4 14:47:47 2006
28: A0802124 Tue Jan 3 20:13:44 2006
29: A0801002 Tue Jan 3 20:13:43 2006
30: A0802124 Tue Jan 3 19:42:34 2006
31: A0801002 Tue Jan 3 19:42:33 2006
32: FFFFFFFF Fri Dec 31 23:59:59 1999:



So obviously:
error A0802124 = hdmi encoder (it is true that from time to time I have artifacts and the image cuts off in hdmi on my 4k tv but on another hd TV much less
error A0801002 = power RSX (nec tokin) and error A0801001 (1 only) = power CELL. Research is progressing, thank you

 

[Djudju]

Hello everyone, I managed to install a CFW, not brick. Then I installed pkg advanced tools. I have thisFirmware Version: 4.88 (build 50731)
Platform ID: CokF10
Product Code: 00 85
Product Sub Code: 00 08
Hardware Config: 4E00FFFF0307BCBF
Syscon Fimware Version: 065D.0000000000000000 (EEPROM: 0000000000000000)

Bringup Count: 3637, Shutdown Count: 3587
Runtime: 220 Days, 11 Hours, 42 Minutes, 49 Seconds

Error Log
01: A0802124 Sun Jan 15 04:12:46 2006
02: A0801002 Sun Jan 15 04:12:45 2006
03: A0802124 Wed Jan 11 16:37:15 2006
04: A0802124 Wed Jan 11 16:37:14 2006
05: A0801002 Wed Jan 11 16:37:14 2006
06: A0802124 Wed Jan 11 03:14:34 2006
07: A0801001 Wed Jan 11 03:14:34 2006
08: A0802124 Mon Jan 9 22:29:31 2006
09: A0801002 Mon Jan 9 22:29:31 2006
10: A0802124 Mon Jan 9 21:55:01 2006
11: A0801002 Mon Jan 9 21:55:01 2006
12: A0802124 Mon Jan 9 03:58:01 2006
13: A0801002 Mon Jan 9 03:58:01 2006
14: A0802124 Mon Jan 9 03:27:42 2006
15: A0802124 Mon Jan 9 03:27:42 2006
16: A0801002 Mon Jan 9 03:27:41 2006
17: A0802124 Fri Jan 6 21:30:13 2006
18: A0802124 Fri Jan 6 21:30:12 2006
19: A0801002 Fri Jan 6 21:30:12 2006
20: A0802124 Fri Jan 6 19:15:53 2006
21: A0801002 Fri Jan 6 19:15:52 2006
22: A0802124 Wed Jan 4 21:22:02 2006
23: A0801002 Wed Jan 4 21:22:01 2006
24: A0802124 Wed Jan 4 19:14:07 2006
25: A0801002 Wed Jan 4 19:14:06 2006
26: A0802124 Wed Jan 4 14:47:48 2006
27: A0801002 Wed Jan 4 14:47:47 2006
28: A0802124 Tue Jan 3 20:13:44 2006
29: A0801002 Tue Jan 3 20:13:43 2006
30: A0802124 Tue Jan 3 19:42:34 2006
31: A0801002 Tue Jan 3 19:42:33 2006
32: FFFFFFFF Fri Dec 31 23:59:59 1999:



So obviously:
error A0802124 = hdmi encoder (it is true that from time to time I have artifacts and the image cuts off in hdmi on my 4k tv but on another hd TV much less
error A0801002 = power RSX (nec tokin) and error A0801001 (1 only) = power CELL. Research is progressing, thank you

Good evening everyone, well, I replaced all the nec tokin above (2 x cell & 2 gpu). Now the console lasts longer but still turns off. I will tackle the other nec tokin, side down. I had a question, once the repairs are done, does the log error log update, it resets if the problems are solved (FFFFFFFF)? Many thanks to the community

 

[Workz_777]

Good evening everyone, well, I replaced all the nec tokin above (2 x cell & 2 gpu). Now the console lasts longer but still turns off. I will tackle the other nec tokin, side down. I had a question, once the repairs are done, does the log error log update, it resets if the problems are solved (FFFFFFFF)? Many thanks to the community

One of the Syscon commands to clear the error log, is "clearerrlog" - (thanks to Vic and Booter who just told me in chat).

Seeing as you have saved your previous error log to text, maybe clear it and see what comes up after you get problems

 

[Djudju]

One of the Syscon commands to clear the error log, is "clearerrlog" - (thanks to Vic and Booter who just told me in chat).

Seeing as you have saved your previous error log to text, maybe clear it and see what comes up after you get problems

 

[Djudju]

thank you, but I can't find a clearerrlog function on syscon via "PS3 advanced tools"

 

[Workz_777]

thank you, but I can't find a clearerrlog function on syscon via "PS3 advanced tools"

No worries, it doesn't matter really (to clear the error log), because everytime there is a new error (out of the 32 listed) it will knock the oldest one off the list anyway.

 

[Djudju]

No worries, it doesn't matter really (to clear the error log), because everytime there is a new error (out of the 32 listed) it will knock the oldest one off the list anyway.

Ok thx,
But precisely it is to see if replacing the nec tokin automatically erases the errors

 

[Djudju]

Hi, my last error log is :
Bringup Count: 3664, Shutdown Count: 3613
Runtime: 220 Days, 20 Hours, 11 Minutes, 48 Seconds

Error Log
01: A0802124 Fri Jan 20 23:22:37 2006
02: A0801002 Fri Jan 20 23:22:36 2006
03: A0802124 Fri Jan 20 22:35:07 2006
04: A0802124 Fri Jan 20 22:35:07 2006
05: A0801002 Fri Jan 20 22:35:06 2006
06: A0802124 Fri Jan 20 19:43:39 2006
07: A0801002 Fri Jan 20 19:43:39 2006
08: A0802124 Wed Jan 18 22:26:27 2006
09: A0802124 Wed Jan 18 22:26:26 2006
10: A0801002 Wed Jan 18 22:26:26 2006
11: A0802124 Wed Jan 18 18:49:06 2006
12: A0801002 Wed Jan 18 18:49:05 2006
13: A0802022 Wed Jan 18 18:39:42 2006
14: A0802124 Mon Jan 16 16:39:09 2006
15: A0801002 Mon Jan 16 16:39:08 2006
16: A0802131 Mon Jan 16 15:51:40 2006
17: A0802124 Sun Jan 15 04:12:46 2006
18: A0801002 Sun Jan 15 04:12:45 2006
19: A0802124 Wed Jan 11 16:37:15 2006
20: A0802124 Wed Jan 11 16:37:14 2006
21: A0801002 Wed Jan 11 16:37:14 2006
22: A0802124 Wed Jan 11 03:14:34 2006
23: A0801001 Wed Jan 11 03:14:34 2006
24: A0802124 Mon Jan 9 22:29:31 2006
25: A0801002 Mon Jan 9 22:29:31 2006
26: A0802124 Mon Jan 9 21:55:01 2006
27: A0801002 Mon Jan 9 21:55:01 2006
28: A0802124 Mon Jan 9 03:58:01 2006
29: A0801002 Mon Jan 9 03:58:01 2006
30: A0802124 Mon Jan 9 03:27:42 2006
31: A0802124 Mon Jan 9 03:27:42 2006
32: FFFFFFFF Fri Dec 31 23:59:59 1999
Now i've a new error : 2131 & 2022. But i've less 1002. I don't understand why. prrrrrrrr

 

[marciolsf]

Ok thx,
But precisely it is to see if replacing the nec tokin automatically erases the errors

No, replacing the tokins (or solving whatever issue your system has) will not erase the old errors. There just won't be any new errors logged.

 

[RIP-Felix]

You can only use PS3 Advanced tools to dump the errorlog. It doesn't feature any commands (such as clearerrorlog). For that you'll need to use UART adapter and Python script.

 

[Cyrano]

Hello friends thank you very much for your help it works my when I turn on the multiman it refuses to open the ja time your help??


Bonjour les amis merci beaucoup pour votre aide sa marche mes quant j'allume le multiman sa refuse de ouvrir les ja temps vôtre aides ??

Please use a translator next time. Good luck my friend.

 

[Workz_777]

Now i've a new error : 2131 & 2022. But i've less 1002. I don't understand why. prrrrrrrr

Did you only replace 2 / 4 of the NEC Tokins on the RSX?

Also, what Tantalums did you use for the replacements?

 

[Djudju]

Did you only replace 2 / 4 of the NEC Tokins on the RSX?

Also, what Tantalums did you use for the replacements?

Hi everyone, thanks for your response. I did something like this (it's not my console, image that comes from the net), but they are the same tantalums (rsx: 2 x 108 & cell: 128). I also wanted to do those on the other side but it's more difficult, there are lots of capacitors next to it, so risky. So I did a test from a video on youtube:

The console takes even longer (motorstorm no longer crashes but uncharted after 2 hours it turns off). Unfortunately I also wanted to resolder the hdmi port and I no longer have a signal, however with the av connection no problem. There it is, thanks

 

[Djudju]

You can only use PS3 Advanced tools to dump the errorlog. It doesn't feature any commands (such as clearerrorlog). For that you'll need to use UART adapter and Python script.

Ok thx Felix

 

[Djudju]

No, replacing the tokins (or solving whatever issue your system has) will not erase the old errors. There just won't be any new errors logged.

Allright Marciolsf, thx

 

[Workz_777]

@Djudju ...bro these AVX Tantalums are no good for the job, the ESR and voltage is too high.

For CELL you need these Panasonic (2R5TPE470M7) 470uF, 2.5V, 7mΩ@100kHz ESR ...here:-
https://www.lcsc.com/product-detail/Tantalum-Capacitors_PANASONIC-2R5TPE470M7_C147773.html

Or because on your RSX the NEC / Tokins are only 1000uF (instead of 1200uF)...

For your RSX, Panasonic (EEFSX0D331E4) 330uF, 2.5V, 4.5mΩ@100kHz ESR ...here:-
https://www.lcsc.com/product-detail...Capacitor_PANASONIC-EEFSX0D331E4_C427165.html

12 x 470uF (3 x 470uF per NEC Replacement) for the CELL

16 x 330uF (4 x 330uF per NEC Replacement) for the RSX

(or for RSX you can also use the 470uF like the CELL = 3 x 470uF per NEC Replacement)

EDIT: Also that Youtube video is no good, because if the NEC is dead, putting 1 x 470uF (piggy-back) per NEC is not going to solve the problem, because it wants 1000uF or 1200uF per NEC.