PS3 (Research/Experimental) - NEC/TOKIN Capacitors Replacement - YLOD

Revak3115 said:
Mine has Held up pretty good also.

This seems to be the only time it has crashed since i replaced 1 CELL NEC.

if you're running CFW could you rebuild database in the XMB as a test for me?(For me the system has to be cool i.e around 50C)

i think i'll remove all the NECs and bridge all the pairs individually(the positive points), that shouldn't hurt it right?
Click to expand...
Nope, Rebuilded the Database, still runs normally, no shutdowns or anything, just had to reinstall Webman as Rebuilding the Database screws with the instalation, other than that normal operation. [emoji23]

Sent from my G8141 using Tapatalk
 
Naked_Snake1995 said:
Nope, Rebuilded the Database, still runs normally, no shutdowns or anything, just had to reinstall Webman as Rebuilding the Database screws with the instalation, other than that normal operation. [emoji23]

Sent from my G8141 using Tapatalk
Click to expand...
Hmm... interesting. Mine only did it when the system was cold, max fan speed using TemMON. More proof that these NECs are just a ticking time bomb lol.

well tomorrow have the reminder caps coming in the mail, so I'll post a update/photo of what I did & how it went when I'm done with that.
 
Revak3115 said:
Hmm... interesting. Mine only did it when the system was cold, max fan speed using TemMON. More proof that these NECs are just a ticking time bomb lol.

well tomorrow have the reminder caps coming in the mail, so I'll post a update/photo of what I did & how it went when I'm done with that.
Click to expand...
Indeed they are, i have to agree with that, looking forward to the results, any information or picture feel free to post, always helps.

Sent from my G8141 using Tapatalk
 
Delita said:
so this is what I meant earlier, just to kind of better explain what I meant. I get continuity between these following pads color coded, and it doesn't matter which pad, top or bottom, they all share.

Is this okay? Can someone else confirm? I feel like the pictures shared in earlier threads make it sound like the outer pads are positive and the inner are negative (ground?) which seemingly means the three light blue pads are really off? Or do the tantalum caps not care about this lol.

Id appreciate others confirming, I am good at following directions, not so much knowledgeable on electrical engineering.

Cheers

https://i.imgur.com/gkCx4GC.png?2
Click to expand...
So following this picture I should bridge both lines with one wire on each side where the red is marked? I am getting my capacitors today and want to make sure I do this correctly.
 
sandungas said:
You just need 1 wire for CELL
And 1 wire for RSX


But you are free to solder together 400000 wires instead of 1... electrically is fine
Click to expand...
So 1 wire for the RSX and one for the CELL, just like i mentioned,but only one is needed, so there is indeed continuity between the tantalums, still waiting on a update from @Luisile from his case,since he almost repalced all the NECs on the board! Time to wrap the reballing myth boys, oh wait it was already wrapped :rolling:
 
Coaleb said:
So following this picture I should bridge both lines with one wire on each side where the red is marked? I am getting my capacitors today and want to make sure I do this correctly.
Click to expand...
Nopes, the red lines painted by delita are connected in internal layers of the motherboard
That red lines are the V_IN of ALL the tokins
 
sandungas said:
No

Please someone upload good photos of a motherboard (both sides) with the tokins removed so we can paint in top of them
Like the photos uploaded by delita, but in bigger size if posible
Click to expand...

COK-001 "Side-A"

COK-001 Side-A.jpg



COK-001 "Side-B"

COK-001 Side-B.jpg
 
Naked_Snake1995 said:
smack them NECs of them with my most preferred method @Cypher_CG89 :oie 19113229e8ymug9p::rolling:
Click to expand...

Cunny Funt < swap the C & F if you catch my drift.... :-p:rolling: Pushing your luck here lad...lol :-p

I have a " little " surprise for your most loved CECHC and other PHATS if you keep pushing your luck lad........

" Say hello to my little friend...... "

Little Friend 1.png

Just so you get the idea of how " Big " my " Little Friend is... "....

Little Friend 2.png

And yes that is mine next to one of my Slims.... It has a date with your Phats lad..... but I am guessing that you would rather use it for some DIY De-liding of CELL's..... :-p :rolling: :rolling: :rolling: :rolling:
So if your going to do it you might as well do it properly and use a proper knife and not some kitchen crap...lol
 
:rolling::rolling:
Cypher_CG89 said:
Cunny Funt < swap the C & F if you catch my drift.... :-p:rolling: Pushing your luck here lad...lol :-p

I have a " little " surprise for your most loved CECHC and other PHATS if you keep pushing your luck lad........

" Say hello to my little friend...... "

View attachment 19293

Just so you get the idea of how " Big " my " Little Friend is... "....

View attachment 19294

And yes that is mine next to one of my Slims.... It has a date with your Phats lad..... but I am guessing that you would rather use it for some DIY De-liding of CELL's..... :-p :rolling: :rolling: :rolling: :rolling:
So if your going to do it you might as well do it properly and use a proper knife and not some kitchen crap...lol
Click to expand...
Are you threatening my THICC Phat boys? :rolling:

That knife, looks smaller than my bick, might as well get a bloody Japanese stainless steel katana to do a delid job :rolling:

If my mind serves me right,i should have one of them Rambo blades in the attic, always saved for a special ocasion of deliding :rolling:
 
Naked_Snake1995 said:
Are you threatening my THICC Phat boys? :rolling:
Click to expand...

Why yes Iam lad... take your pic> that Black Carbon Steel Combat Knife, got a 3ft survival machete in the garage, several sizes and weights of sledge hammers and my rifle.. whats your poison/ prefered method of execution for them PHATs...? Or I could make some home made thermite and melt them or homemade gunpowder and blow them up..? The choice is yours lad.....:-p:eek::D:cool:

sandungas said:
But dont use the knife to eject discs dude ! :P
little-friend-2-png.19294
Click to expand...

Am not as daft as @Naked_Snake1995 ... I use it for turning of the PS3 at long range...... :-p:-p

Naked_Snake1995 said:
Did it once on a Zephyr RRoD XBOX360 jammed disc drive, worked like a charm, shame the chrome trim didnt last "Microsoft Quality Seal"
Click to expand...

My point proven right here.....^^^^^^..... :-p:D
 
Cypher_CG89 said:
Why yes Iam lad... take your pic> that Black Carbon Steel Combat Knife, got a 3ft survival machete in the garage, several sizes and weights of sledge hammers and my rifle.. whats your poison/ prefered method of execution for them PHATs...? Or I could make some home made thermite and melt them or homemade gunpowder and blow them up..? The choice is yours lad.....:-p:eek::D:cool:



Am not as daft as @Naked_Snake1995 ... I use it for turning of the PS3 at long range...... :-p:-p



My point proven right here.....^^^^^^..... :-p:D
Click to expand...
3t5sj5.jpg
 
You must log in or register to reply here.

Similar threads

Back
Top