PS3 Brick while using PS3Xploit incorrectly

[Metinfield]

Thank you very much for your bkpps.bin file

 

[pink1]

Thank you very much for your bkpps.bin file

Did it get you going again?

 

[Metinfield]

shuan tested ps3 works

Did it get you going again?

 

[pink1]

Put that dump in a safe place & you can use it it you ever run into a problem like this again

 

[DeViL303]

For a brick like this one from using the exploit on cfw do we just patch the dump for cfw again?
I'm trying to get fixing these down.

I don't know for sure but I would say yes, once the dump has been fixed then it just needs the standard cfw patch applied again.

 

[pink1]

I don't know for sure but I would say yes, once the dump has been fixed then it just needs the standard cfw patch applied again.

Yep I just used BwE NOR Validator to patch for 4.40 no fsm

 

[Metinfield]

Spare Buyer Gratitude for your interest and help

 

[pink1]

Spare Buyer Gratitude for your interest and help

We all need a little help at sometime, I'm glad we could get you fixed without too many problems.

 

[mrisvan]

all master of kings very very thanx

 

[electronicsrepair]

plz help fix a uncompatible exploited console
her is the link to the dump, idps no need to worry about
thanks a lot
CECH-30xx
lowest downgradeable:3.60
exploit v1.0

 

[pink1]

plz help fix a uncompatible exploited dump
her is the link, idps no need to worry about
thanks a lot

I don't mind helping anyone out. All I ask is that they read up and understand what they are doing, give us as much info as you can & if it comes to the point that you need someone to take a look at your dump for you put it somewhere we can get it without needing an account.
I can't use 4shared.

 

[matnyaga]

plz help fix a uncompatible exploited console
her is the link to the dump, idps no need to worry about
thanks a lot
CECH-30xx
lowest downgradeable:3.60
exploit v1.0

Hey dude,

have you checked out the very first page of this thread? There are a couple of instructions to help you out. If you follow them your PS3 will be just fine (if you have a Hardware flasher e.g E3 flasher)

 

[electronicsrepair]

I know how to inject coreos 482, using ps3dump checker and other but thers also two other errors need to be fixed but don't have much understanding..thanks

 

[pink1]

What are the errors you're getting?

 

[electronicsrepair]

What are the errors you're getting?

I have uploaded the dump,

 

[littlebalup]

I know how to inject coreos 482, using ps3dump checker and other but thers also two other errors need to be fixed but don't have much understanding..thanks

Your dump is totally corrupted. Make a proper dump befor to attempt to fix ROS's.
You should have only a warning for sku and maybe another for one ROS hash (depend if you installed OFW 4.82 twice before exploit or not).

 

[electronicsrepair]

Hi, thanks for all the answers, i think the ps3 is gone forever, since made only one backup, the uploaded one, any suggestions?..

 

[watq]

You can use the E3 to dump the console & with a hex editor replace CoreOS with one from 4.82 OFW.

Please help i have problem.the ps3 where brick but have dump a nand min version 3.60 using e3 flasher I don't know how to create coreOS

You can use the E3 to dump the console & with a hex editor replace CoreOS with one from 4.82 OFW.

Can I upload the nor you edit for me please

 

[pink1]

Please help i have problem.the ps3 where brick but have dump a nand min version 3.60 using e3 flasher I don't know how to create coreOS


Can I upload the nor you edit for me please

Try what is posted here. The link has the file and tools you need. If you have any problems just let us know.

I wished to give an update on the PS3 situation. It is presently working, thank you to everyone on this thread and especially Pink who was patient with me while helping me out.

@playerkp420 I was previously using the file "ofw_flash_482.hex" and tried to use HxD to input the file manually. It didn't work....lol

To anyone out there who might be in the same situation I was please follow the guide down below:

http://www.logic-sunrise.com/forums...ne-ps3-suite-a-un-flash-ps3xploit-malheureux/

It's not in English but it is pretty self-explanatory.

Just a couple of things to I discovered(Please correct me if I'm wrong):

- Since your PS3 isn't coming on, you'll need to solder a wire at the back of your motherboard. They are variations depending on your board type the name of your board (located at the back) plus tristate to GND on to Google. It'll ensure your PS3 stays ON.
- Also ensure, you have multiple copies of your dump. I had 6 but I think 4 should be fine. Make sure they are identical by using HxD and use Ps3Dumpchecker to ensure they are fine before doing anything else.
- If your E3 flasher just has a red light (i.e the blue lights don't come on) you've probably put the cable in backwards.
- After you patch your dump write it twice with the E3 flasher (100000) and (000000) where 1 is up
- Afterwards, immediately dump it again on to your SD Card and use HxD to check if the dump matches the patched dump stored on your computer.

 

[Albon]

Hello,
I have a similar problem : a compatible CECH 2004 PS3 which I tried to patch with PSXploit. But I turned off the PS3 too soon, before the Green message.
After Power on, it was shutting down after 2s with blinking red.
I dumped the Nor with my E3 several times. I only have 2 errors Ros0 and Ros1 Hashes

Then I tried everyting suggested here :
I tried to patch dump with PS3 dump checker noFSM Ferrox 4.82 patch
With CoreOS4.82 OFW patch
With 3.55 patch

Console starts with black screen, no HDD activity LED, no access to recovery (no beeps while holding the Power button)... I'm out of ideas to try and I'd really appreciate any help.