PS3 PS3DumpChecker

I had a brick in my ps3 but I solved it, now the problem is that when I put the backup of the flash extracted with rebug toolbox and put it with the e3 flasher it remains in black screen. I have 3 flash dumps and none works. the console was at 4.82 and the dumps I see are lower there is some problem with that?
 
CYB3R18 said:
I had a brick in my ps3 but I solved it, now the problem is that when I put the backup of the flash extracted with rebug toolbox and put it with the e3 flasher it remains in black screen. I have 3 flash dumps and none works. the console was at 4.82 and the dumps I see are lower there is some problem with that?
Click to expand...
By overwriting flash, you overwrite info about latest firmware's. So this shouldn't be the issue. Does it stay on green led?
 
kozarovv said:
By overwriting flash, you overwrite info about latest firmware's. So this shouldn't be the issue. Does it stay on green led?
Click to expand...
If you refer to the LED to turn on the console if, what happens is that once everything is finished it simply does not give a signal, the console lights perfectly something that it did not do before and it was turned off just turn it on. after welding the tristate to the e3 flasher and put one of the 3 dumps that had extracted with hombrew and starts correctly but no signal
 
CYB3R18 said:
If you refer to the LED to turn on the console if, what happens is that once everything is finished it simply does not give a signal, the console lights perfectly something that it did not do before and it was turned off just turn it on. after welding the tristate to the e3 flasher and put one of the 3 dumps that had extracted with hombrew and starts correctly but no signal
Click to expand...
If it starts correctly with old dumps (solid green light), then try to reset display settings. Turn off PS3, and while turning it on keep pressed power button until you here another beep.
 
kozarovv said:
If it starts correctly with old dumps (solid green light), then try to reset display settings. Turn off PS3, and while turning it on keep pressed power button until you here another beep.
Click to expand...
When i hold down power button console beeps 1 when starting, and after 20 sec beep again and turn of. No beeps between start and off. When i start it again without holding power button still no signal. the recovery mode is not present either
 
CYB3R18 said:
When i hold down power button console beeps 1 when starting, and after 20 sec beep again and turn of. No beeps between start and off. When i start it again without holding power button still no signal. the recovery mode is not present either
Click to expand...
Do you tried read again dump that you are flashed? To make sure it flashed correctly? Also you should remove trislate to make it boot.
 
CYB3R18 said:
I had a brick in my ps3 but I solved it, now the problem is that when I put the backup of the flash extracted with rebug toolbox and put it with the e3 flasher it remains in black screen. I have 3 flash dumps and none works. the console was at 4.82 and the dumps I see are lower there is some problem with that?
Click to expand...

You must byte reverse your flash backup if you want to use it with e3 flasher. You can use pyPS3patcher or flowrebuilder for that.
 
kozarovv said:
Do you tried read again dump that you are flashed? To make sure it flashed correctly? Also you should remove trislate to make it boot.
Click to expand...
If I removed the cable that had soldered from the flex cable to the nor tristate. Since my brick was that just turned on the console went off to the second. Everything started by modifying an official firmware with CFW files and installing it in a console with CFW. I have 3 dumps of the flash which the E3 Nor Dump Checker V1.0 tell me is wrong. With PS3DumpChecker v1.0 Build 491 in some it tells me that it is fine and in some cases it shows me 2 errors of ROS0 hash and ROS1 hash.
 
littlebalup said:
You must byte reverse your flash backup if you want to use it with e3 flasher. You can use pyPS3patcher or flowrebuilder for that.
Click to expand...
I must use Byte reverse and extract to NOR dump file? with FlowRebuilder v.4.1.3.2?
I get a file called Flash.BIN.REV with errors says the program
 
2 renamed to bkpps3.bin dumps get this 2 erros

94B.png
 
CYB3R18 said:
I must use Byte reverse and extract to NOR dump file? with FlowRebuilder v.4.1.3.2?
I get a file called Flash.BIN.REV with errors says the program
Click to expand...
Use this one : http://www.ps3hax.net/showthread.php?t=95794
Then select "Byte reverse a dump" operation with your *.hex or *.NORBIN file then execute.
It should create a *.swap.bin file that you must rename as "bkpps3.bin" to be used with your flasher.

Edit:
Your screen shows non-reversed dump...
About ROS, PS3dumpChecker doesn't recognize other ROS than OFW. Use PyPS3checker instead.

If you're lost, send me your dump by private message.
 
Last edited:
littlebalup said:
Use this one : http://www.ps3hax.net/showthread.php?t=95794
Then select "Byte reverse a dump" operation with your *.hex or *.NORBIN file then execute.
It should create a *.swap.bin file that you must rename as "bkpps3.bin" to be used with your flasher.

Edit:
Your screen shows non-reversed dump...
About ROS, PS3dumpChecker doesn't recognize other ROS than OFW. Use PyPS3checker instead.

If you're lost, send me your dump by private message.
Click to expand...

I have used flowrebuilder 5.2 and CEX-FLASH.EID0.swap.bin is created correctly. It is normal that if I examine with HxD show this

01E.png


I do not know how to use PyPS3checker :(

I do not know if I'm leaving something or the dumps that I take with HB do not work, I send you the originals that I have for private and if you would do me the favor of reviewing them I would appreciate it very much buddy.
 
CYB3R18 said:
I have used flowrebuilder 5.2 and CEX-FLASH.EID0.swap.bin is created correctly. It is normal that if I examine with HxD show this

01E.png


I do not know how to use PyPS3checker :(

I do not know if I'm leaving something or the dumps that I take with HB do not work, I send you the originals that I have for private and if you would do me the favor of reviewing them I would appreciate it very much buddy.
Click to expand...

yes it's normal,
Reversed, 6D 65 74 6C 64 72 (metldr) become 65 6D 6C 74 72 64 (emltrd)
 
I have made a series of videos about the brick on my channel, I was hoping to solve it since people like to watch videos like that and I think they are interesting even if they are old gen. Thanks for your help




Edit: surely they will not understand anything of what I speak..:) I am Spanish but maybe they can see the problem which I am having
I would have liked to record the part of patching the dumps that I guess I will do in another console but as I do not really know how it works with dumps extracted with HB
Regards
 
I already know how the script patcher.py works for nofsm 4.82 and revert the dump. What I do not understand is the following as if I can install a 4.82 cfw or 4.82? how to modify the SDK for example that allows me to install a 3.55 once put the dump in the console. How do I change the values to install a firmware to my liking?
 
You must log in or register to reply here.

Similar threads

Back
Top